Vol 5, No 2 (2016)

Chief Editor

Muhamad Fitri ST, M.Si, Ph. D, Universitas Mercu Buana, Indonesia

Editorial Board

Prof. Dr. Ir. Chandrasa Soekardi, Universitas Mercu Buana, Indonesia
Dr. Kontan Tarigan, Universitas Mercu Buana, Indonesia
Dr. Nurdin Ali, Universitas Syiah Kuala, Indonesia
Dr. Poempida Hidayatulloh, Universitas Mercu Buana, Indonesia
Prof. Dr. Bambang Suharno, Universitas Indonesia, Indonesia
Dr.-Ing. Pudji Untoro, Universitas Surya, Indonesia
Dr.-Ing. Ir. Kusnanto Kusnanto, Universitas Gadjah Mada, Indonesia
Dr. Sagir Alva, Universitas Mercu Buana, Indonesia
Dr. Abdul Hamid, Universitas Mercu Buana

Editorial Staff

Bakri Rio Rahayu, Universitas Mercu Buana, Indonesia
Yananto Mihadi Putra, Universitas Mercu Buana, Indonesia
Goffari Maulana, Universitas Mercu Buana, Indonesia

Managing Editor

Ir. Haris Wahyudi, M.Sc, Universitas Mercu Buana, Indonesia
Muhamad Fitri, ST, MSi, PhD. Universitas Mercu Buana, Indonesia

Notifications

Journal Content
Browse

Keywords Age Replacement,downtime, optimal perencanaan perawatan dan preventive maintenance Airfoil, Qblade, Turbin Angin, Daya Barcode id, PLC, Raspberry Pi, PLC with Barcode Integration COP Co-firing, Boiler Pulverizer Coal, Sawdust, Emisi gas buang Composite fibers, weaving pattern, reinforcement, mechanical test, ballistic test Efisiensi Kata kunci: exhaust gas temperature margin, air mode, high pressure compressor clearance control Kendaraan listrik, baterai, service life, pengisian baterai, pengosongan baterai. Kursi Plastik MRT Jakarta Panel Surya Programable Logic Controller (PLC), Infrared Refrigeran, ODP, GWP, R22 Safety Factor Schedule Oil Sampling, Sistem Pelumasan, Diesel Engine, FMEA Shaft,Material,CAD egg incubator, tenaga surya, photovoltaic, unggas emergency landing loads fiber diameter, morphology, mechanical characteristics, tensile strength, Young’s modulus floor support structure

Aims and Scope
Peer Review Policy
Author Guidelines
Editorial Board
Abstracting & Indexing
Publication Ethics
Open Access Statement
Plagiarism Policy
Copyright and License
Article Processing Charge
Contact Us

Language

User

Font Size

Current Issue

Vol 5, No 2 (2016)

Table of Contents

Articles

PENGARUH TEMPERATUR DAN LINE SPEED PADA PROSES PEMBUATAN KABEL OPTIK YANG MENGALAMI KECACATAN DISELUBUNG KABEL PADA MESIN EXTRUDER

10.22441/jtm.v5i2.709

Bahrul Ikam

PDF

37-49

PERHITUNGAN TEGANGAN PIPA DARI DISCHARGE KOMPRESOR MENUJU AIR COOLER MENGGUNAKAN SOFTWARE CAESAR II 5.10 PADA PROYEK GAS LIFT COMPRESSOR STATION

10.22441/jtm.v5i2.710

Arief Maulana

PDF

50-63

PERANCANGAN MESIN PENGUPAS DAN PEMISAH KULIT BUAH KOPI KERING

10.22441/jtm.v5i2.711

Vinantius Kelik, Hengky Hengky, Daniel Kurniawan

PDF

64-70

ANALISA PENGARUH TEMPERATUR UDARA MASUK TERHADAP TEKANAN DAN TEMPERATUR GAS BUANG PADA PLTD PULO PANJANG BANTEN

10.22441/jtm.v5i2.712

Sandi Setiawan

PDF

71 -76

REKAYASA BAHAN CAMPURAN BETON DAN INSTALASI PENGOLAHAN AIR UNTUK PENUNJANG PRODUKSI DENGAN MEMANFAATKAN LIMBAH IPAL DI PT X

10.22441/jtm.v5i2.713

Zaenal Zaenal

PDF

77-80

PENGARUH TEKNIK PENYAYATAN PAHAT MILLING PADA CNC MILLING 3 AXIS TERHADAP TINGKAT KEKASARAN PERMUKAAN BENDA BERKONTUR

10.22441/jtm.v5i2.714

Irawan Irawan

PDF

81 -89

Jurnal Teknik Mesin (JTM)
Program Studi Teknik Mesin, Fakultas Teknik, Universitas Mercu Buana
Jl. Meruya Selatan No. 01, Kembangan, Jakarta Barat 11650, Indonesia
Email: mesin@mercubuana.ac.id
Telp.: 021-5840815/ 021-5840816 (Hunting)
Fax.: 021-5871335

JTM is indexed by the following abstracting and indexing services:

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.